×
×
| DIGITAL | ANALOG | ||
|---|---|---|---|
| LASER | KNIFE | ||
| No need | Mold Design | Every time for new design | |
| No need | Every 1 month | Consumables | Almost everyday |
| Immediately | 1 day | Lead-time | 2~3 days |
| Much Acceptable | Short-run job | Less acceptable | |
| Easy | Acceptable | Complicated Design | Difficult |
| Small footprint | Working space | Factory | |
| Anyone | Operator Level | Highly professional | |
| 10 min | Setup time | More than 1hour | |
Let’s compare the digital die-cutting method with the existing analog method.
First, there is a difference in preparing cutting line.
Since the steel die is made through bending as in a typical manufacturing way of analog method, which normally takes 3~5 hours, it is difficult to manufacture at the first place. However, the digital method uses a design program, and takes only 1 minute to prepare.
The analog method takes an hour to set-up, but with the digital method, the file can be simply saved and loaded again. If the cutting line has to be modified, it can be done immediately with the digital method. On the other hand, re-manufacture required for each error or requests for design changes are difficult to accommodate in the analog method.
Now the cutting has been completed. While the digital method simply saves the file for the completed cutting line, the analog method requires some separate storage area.
In general, the digital die-cutter, any-CUT III, can result in tenfold savings in terms of time and cost over the analog method. “Now, the digital laser die-cutter any-CUT III
can provide convenience and speed to all your label post-processing.
[vc_row][vc_column width=”1/1″][vc_column_text][contact-form-7 id=”21500″ title=”Live demo”][/vc_column_text][/vc_column][/vc_row]
[vc_row][vc_column width=”1/1″][vc_column_text][contact-form-7 id=”21425″ title=”catalogue_any-CUT II”][/vc_column_text][/vc_column][/vc_row]
[vc_row][vc_column width=”1/1″][vc_column_text][contact-form-7 id=”21426″ title=”catalogue_any-CUT II”][/vc_column_text][/vc_column][/vc_row]
[vc_row][vc_column width=”1/1″][vc_column_text][contact-form-7 id=”21425″ title=”catalogue_any-CUT II”][/vc_column_text][/vc_column][/vc_row]
[vc_row][vc_column width=”1/1″][vc_column_text][contact-form-7 id=”21404″ title=”catalogue_any-PACK-system”][/vc_column_text][/vc_column][/vc_row]
[vc_row][vc_column width=”1/1″][vc_column_text][contact-form-7 id=”21141″ title=”catalogue_any-CUT II”][/vc_column_text][/vc_column][/vc_row]
[vc_row][vc_column width=”1/1″][vc_column_text][contact-form-7 id=”21124″ title=”catalogue_anytron_Flow”][/vc_column_text][/vc_column][/vc_row]
[vc_row][vc_column width=”1/1″][vc_column_text][contact-form-7 id=”20492″ title=”catalogue_anytron_RIP”][/vc_column_text][/vc_column][/vc_row]
[vc_row][vc_column width=”1/1″][vc_column_text][contact-form-7 id=”19546″ title=”catalogue_anycut1″][/vc_column_text][/vc_column][/vc_row]
[vc_row][vc_column width=”1/1″][vc_column_text][contact-form-7 id=”19550″ title=”catalogue_anycut3″][/vc_column_text][/vc_column][/vc_row]
[vc_row][vc_column width=”1/1″][vc_column_text][contact-form-7 id=”19555″ title=”catalogue_anyblade”][/vc_column_text][/vc_column][/vc_row]
[vc_row][vc_column width=”1/1″][vc_column_text][contact-form-7 id=”19559″ title=”catalogue_anypack”][/vc_column_text][/vc_column][/vc_row]
[vc_row][vc_column width=”1/1″][vc_column_text][contact-form-7 id=”19563″ title=”catalogue_anyslitter”][/vc_column_text][/vc_column][/vc_row]
[vc_row][vc_column width=”1/1″][vc_column_text][contact-form-7 id=”19570″ title=”request popup”][/vc_column_text][/vc_column][/vc_row]
[vc_row][vc_column width=”1/1″][vc_column_text][contact-form-7 id=”20063″ title=”catalogue_anyjet”][/vc_column_text][/vc_column][/vc_row]
[vc_row][vc_column width=”1/1″][vc_column_text][contact-form-7 id=”20476″ title=”Distributor pages”][/vc_column_text][/vc_column][/vc_row]
[vc_row][vc_column width=”1/1″][vc_column_text][contact-form-7 id=”19530″ title=”catalogue_any002″][/vc_column_text][/vc_column][/vc_row]